More and more people will choose to install a solid-state tough drive so as to boost the overall performance on the laptop and resolve the problem of personal computer freeze-up. In addition, as the value with the solid-state hard drive has dropped, I lately asked Xiaobai about installing the program in to the solid state The two issues of non-destructive migration to solid state are fairly frequent. Next, Xiaobai will teach you the way to deal with these two circumstances.


Installation directions
The solid state installation system will be the same because the mechanical tough disk installation, except that in case you do not confirm no matter if your strong state would be the default primary disk, it is suggested that you simply pick manual settings throughout the installation in the technique, which requires you to produce a PE initially Atmosphere, no matter if it can be essential for direct installation or lossless migration, the two popular production procedures are U disk production and on line production

U disk generating PE
You only must comply with the U disk installation tutorial (click to jump) to enter PE and total (that is certainly, the third step inside the text), adhere to the tutorial under



Make PE on the web
Comply with the on the internet installation tutorial (click to jump), inside the ninth step is to decide on DOS automatic installation, but we wish to install to solid state, so we really need to manually set up, choose [PE] mode





Strong State Drive Installation System
Just after entering the PE, open the installation tool, pick the target partition (decrease left corner), select it and click 'Install System' on the bottom suitable. Note that the target partition ought to be selected from your strong state drive. If recover files from disk image are not positive which one particular, you'll be able to open the ' My personal computer 'to see which can be your solid state disk



In case you ca n’t select your SSD,
We first open the partition master or partition assistant, click the rapid partition to format the SSD
You can also delete the strong state drive and after that partition the strong state drive (it may be a zone),
Verify the MBR for the partition table kind. When you need 4K alignment, change the 2048 sector at the bottom proper to 4096.
[ recover files from disk image is just not vital, you could skip the partition and format directly]



If there is only a single partition and also the format is MBR, it is possible to click Format without the partition (the red icon above)



Select a very good format, generally the default format, [NTFS] click format



Soon after completion, re-open the installation tool, select the method, click (reduce proper corner) to set up, if a pop-up prompt appears, choose to continue or OK




Repair boot
Right after installation, usually do not restart the laptop right away, repair the boot first,
The above steps have made adjustments for the partition. From the point of view of some users, some models can't be automatically repaired by boot. For safety motives, you nevertheless ought to manually perform boot repair. The following 3 approaches is often completed soon after the order is completed. personal computer.


strategy 1
1. We found the Windows boot repair immediately after getting into the PE interface, and double-clicked to open it.

2. After opening, a boot partition that needs to be repaired seems, pick to click the C drive, in case your strong state is just not the C drive, click the corresponding with the solid state
three. Right after entering, we are able to see a green interface, in the interface we are able to see a [start repair]

4. We click or press the number 1 to repair, and after that enter the repair, wait a bit bit.

5. Then it can pop as much as prompt that the repair has been thriving, click [Exit] or press the number 2 to exit, restart the machine


Technique Two
Normally the default is around the disk you installed



Technique Three
Still open my personal computer within the PE interface, choose the Y drive

Click to open X86

Open current folder

Open Dism ++ 10.1.27.1

Should you are installing a 64-bit method, open the corresponding Dism ++ * 64.exe
Installed 32-bit method, just open Dism ++ * 86.exe

Immediately after opening, a prompt window pops up, click OK

Then the agreement pops up, click accept

Immediately after entering, click and click the C disk, and after that click [Open Session], that is based on which disk the solid state is in and then adjust the choice


Click Toolbox on the left, click Guide Repair

Popup prompt, pick OK

When completed, click OK, close the tool, unplug the U disk, restart the computer, and wait for the final installation





set up driver
Right after the installation is effective, pull out the U disk and restart. If your graphics card is often a new model, it can be suggested that you just do not check the graphics card driver installation when the driver is installed. Wait for the method to be installed and after that download the driver installation around the computer's official web site







System non-destructive migration to solid state
Very first connect the new SSD to the laptop, enter the PE environment, open the partition assistant on the desktop, choose 'Migrate System to Strong State Drive' within the wizard menu on the left, and choose the new SSD. A blank partition is needed for program migration, along with the capacity with the blank partition ought to be higher than the applied capacity of your current technique disk, or it is possible to decide on to possess the partition assistant automatically delete the partition and re-plan. Then click subsequent.


The partition assistant will adjust the partition capacity in the SSD. By default, the partition is as huge because the current system disk. Naturally, so long as it really is bigger than the present program disk made use of capacity, you are able to adjust it at will. Just after clicking Next, there will probably be a note window, just click 'Finish'.

You may see that a 'system' partition has appeared on the SSD, and it can be exactly the identical because the original method disk. At this time, the program partition and internal information on the SSD are just an empty shell. There is absolutely no actual partition and no data.

Click the 'Submit' button within the upper left corner in the window, a prompt window pops up, click 'Execute', so that the actual partition and file copy procedure are going to be carried out. The pc needs to be restarted soon after completion. Please be patient and wait for the job to complete before restarting.

Right after the laptop or computer restarts, it enters the ProOS interface and automatically performs partitioning and file copying. Right after the method is copied, it's going to automatically restart. If you enter the technique, it is possible to see that there's a disk exactly precisely the same as the original system disk, which stores the information of your original system disk. Even though the complete approach will take some time, it is much more essential than installing the program and software program. It is considerably faster. If there is a boot error, you are able to make use of the above boot repair technique to fix it.