Pros And Cons Of Elastomeric Coatings

If you believe you'll be conserving the roofing decking plywood (not replacing it), then you may save yourself some clean-up trouble by getting rid of the components first and after that peeling up the rubber! Information of water damage on camper roofing system. More water harmed locations on Recreational Vehicle roofing system decking. There was nothing truly dreadful that made me feel like I was going to fall through, but absolutely a lot of damage and I was getting the sensation I would be replacing a lot of the roof decking plywood.

What Are Elastomeric Coating And How Are They Used

Pop Over To This Website: roof leak repair Tucson - DCRoofingArizona.com http://johnnyxowf016.huicopper.com/roof-coating-specialists

I chose the easiest one initially, a vent cap from a cooking area sink pipes vent pipeline. Beginning to scrape caulk and sealant. I used a stiff scraper with a chisel-like blade and simply began spying and chipping and scraping and hacking. There is no other method around this, you simply need to begin digging until you expose the screw heads.

Unscrewing the screws in vent cap. The screws on this vent cap were hex-head metal screws so I utilized a little socket motorist to eliminate them. Some came out tidy. Others were rusted and I needed to utilize a vice-grip pliers to get the heads and turn them gradually.

I discovered an old wasp nest inside the vent cover. This is a sight I'll probably need to get utilized to, discovering the remains of animal habitation in every nook and cranny. I invest an awful great deal of my time producing good wildlife habitat in my yard so I do not get angered when an animal chooses to set up home in my Recreational Vehicle.

Your Place: Elastomeric Roof Coatings Last Long, If Not A Lifetime

Fortunately nobody was house in this old nest so I just tossed it. Perhaps I'll put a screen over it when changing it. Which brings us to the next point. You should attempt not to damage these pieces (like vent covers and caps) as you're scraping off the old caulk and sealant just in case you need to use them again.

(Guess I'll find out when the roofing system is done!) Prying up the vent cap and removing the last ring of rubber roof underneath. So I pried up the rest of the cap and scraped up the staying rubber roofing and butyl tape and putty and 25 years of other gunk and here's how it looks cleaned up.

Consider An Elastomeric Roof Coating

One down, 7 more components to go. Next I decided to deal with the only roofing system ventilation fan that my camper has. My roof vent likewise had a vent cover over it. So I started scraping the gunk from those screws. Beginning on the roofing vent. Hardware exposed on roofing system vent cap, the first nut came off tidy.

The Ultimate Guide To Rv Roof Coating

Bolt is spinning. The fasteners on this RV roofing vent cover were nuts on little bolts. The first one came off fine with an extension socket set. The 2nd one simply started spinning, meaning the bolt was not fixed in location but turning in addition to the nut. Disappointment. A peek at the hardware holding down the roof vent cover.

Elastomeric Roof Coating - Can You Apply It Yourself?

I didn't have any great way to hold the bolt in location so rather I decided to saw through the bolts with a reciprocating saw. Sawing through bolts on roof vent cover. I used a cordless reciprocating saw with a metal-cutting blade however it was challenging to get the blade flat sufficient to reach the bolts so near the roof deck. Most were so old and rusted that they sheared off when I unscrewed then with a lot of force. Loosening the brackets that held the vent cover in location. Then I scraped more caulk and roofing system sealant off the flange of the roof vent itself. I quickly found there were no more screws or hardware holding it down so I quit on the scraping and went inside the RV After scraping the caulk and sealant from flange of roofing system vent, no more screws! Unscrewing the inside cover plate of roofing vent fan in RV restroom.

A couple sheared off with a great deal of force, however two would not budge. So I needed to drill out the screw heads. I selected a drill bit near the size of the shaft of the screws that I had currently taken out and started drilling. Choosing a drill bit for drilling out a screw head.

Shatterproof glass recommended. So I drilled out the heads, one popped off and the other I was getting upset with and gave it a tug prior to it was drilled through. Instead of popping off the screw head, the plastic simply disappeared around the hot screw head. Whoops. Hope I do not need to recycle this cover.

If not, I'll need larger screw heads when re-assembling. Cover plate eliminated from roof vent. Next I discovered little corner brackets with hex-head bolts holding them in. I unscrewed them (all came out great fortunately) and took out the brackets and little white plastic spacers. Unscrewing corner brackets in roof vent.

Elastomeric & Emulsion Roofing

All corner brackets removed, all set to pull out. Once the brackets were out I went back up top to pry out the the roofing system vent. Then I scraped up all the remaining gunk and rubber roofing. Raising off the old roof vent. There are 2 wires running to the roofing system vent (a black hot wire and a white neutral wire) that you'll require to clip to eliminate the old vent.