|
|
, DWL-G700 Maximus Sektor 2.4-17-120.
, :
/etc/network/wifi/general
#Set ESSID of wirelless Infrastructure Network
iwpriv wlan0 set_mib ssid="ASP24"
#Uncomment and Set prior bssid to connect
#iwpriv wlan0 set_mib bssid2join=000000000000
iwpriv wlan0 set_mib hiddenAP=0
#Set Mode: 8 – Client;16 – AP; 32 – AdHoc
iwpriv wlan0 set_mib opmode=16
#Set Regulatory Domain:
# "3" – 13 channels available, "6" – 14 channels available.
# FCC=1;IC=2;ETSI=3;SPAIN=4;FRANCE=5;MKK=6
iwpriv wlan0 set_mib regdomain=3
#Set Channel here
iwpriv wlan0 set_mib channel=5
#Set Initial Gain: in range 0-7
# It seems to be sens but maybe not. Just test
iwpriv wlan0 set_mib initialGain=3
#Set TransmitPower for CCK(802.11b) modulation
# Please Change it in variable
CCKPOWER=1a
iwpriv wlan0 set_mib TxPowerCCK=`ader $CCKPOWER 14`
#iwpriv wlan0 set_mib TxPowerCCK=1010101010101010101010101010
#Set TransmitPower for OFDM(802.11g) modulation
# Please Change it in variable
OFDMPOWER=1a
iwpriv wlan0 set_mib TxPowerOFDM=`ader $OFDMPOWER 162`
#iwpriv wlan0 set_mib TxPowerOFDM=1010101010101010101010101010101010101010
10101010101010101010101010101010101010101010101010101010101010101010101010101010101010
iwpriv wlan0 set_mib basicrates=1008
iwpriv wlan0 set_mib oprates=1008
iwpriv wlan0 set_mib fixrate=1
iwpriv wlan0 set_mib autorate=1
iwpriv wlan0 set_mib band=2
iwpriv wlan0 set_mib bcnint=100
#RTS/CTS Threshold
iwpriv wlan0 set_mib rtsthres=2346
iwpriv wlan0 set_mib fragthres=2346
iwpriv wlan0 set_mib expired_time=10000
iwpriv wlan0 set_mib dtimperiod=1
iwpriv wlan0 set_mib show_hidden_bss=0
iwpriv wlan0 set_mib preamble=1
iwpriv wlan0 set_mib shortretry=6
iwpriv wlan0 set_mib longretry=6
iwpriv wlan0 set_mib Diversity=0
iwpriv wlan0 set_mib DefaultAnt=0
iwpriv wlan0 set_mib RFChipID=7
iwpriv wlan0 set_mib led_type=7
#G protection
iwpriv wlan0 set_mib disable_protection=0
#For bridged mode set this parameters
# Nat2.5 is technology to change the source MAC to MAC of Wlan-interface
# be carefull it says disabled, so make inverse in your decision
iwpriv wlan0 set_mib nat25_disable=1
# Macclone says all about itself. It just takes MAC of ETHERNET device on other end of line
# and take it for Wlan-interface. be carefull if this enabled it must be one device on a line.
iwpriv wlan0 set_mib macclone_enable=0
iwpriv wlan0 set_mib dhcp_bcst_disable=0
#Block packets between clients connected
# 0 – disable; 1 – block relay;2 – block relay but passup
iwpriv wlan0 set_mib block_relay=0
