1. Operating procedures of floating fish feed  device

 

( 1) Precautions before starting  as well as after  quiting

 

①  Examine all parts of fish feed  drifting pellet making  maker, especially the  attaching screws and  support  screws of each section of the puffing chamber, the  linking bolts  in between the motor base  as well as the  structure,  and also the bolt connection  in between the puffing chamber  and also the frame,  as well as there  have to be no looseness;

 

②  By hand rotate the  major shaft,  currently, there  ought to be no rubbing  audio in the fish feed  drifting pellet making  equipment puffing  dental caries;

 

③  Beginning the feeding auger of fish feed  drifting pellet making  equipment,  examine its stepless high-speed  efficiency,  and also  need  typical  procedure;

 

④  Inspect and clean the water and gas paths  prior to  beginning the fish feed  drifting pellet making  device, and all filters need to be  cleansed;

 

1.


2.

Related post： fish feed mill plant

 

⑤  Prior to  beginning the fish feed  drifting pellet making  equipment, check whether the wiring of the electric control part is correct, whether the  turning of each  electric motor is correct, and whether the control is  trustworthy;

 

⑥ After the fish feed  drifting pellet making  device is  quit, you  have to  put on high-temperature gloves, quickly  eliminate the discharge mold,  and also  right away  tidy it while it is  warm,  as well as  begin the  primary  electric motor to  clear the material  collected in the  blowing  dental caries. When the corn is  blown, soybean powder  ought to be  included The  product is rinsed  tidy;

 

⑦  Focus on  safety and security when  discharging the  device, and do not stand in front of the  maker to avoid danger caused by residual  stress in the fish feed floating pellet making  equipment  tooth cavity;

 

⑧ After the fish feed  drifting pellet making  device is running  generally, it shall not be shut down at will.

 

( 2) Power on

 

①  Prior to  beginning the fish feed  drifting pellet making  maker,  examine the fasteners, and there  need to be no looseness;

 

② Ensure the normal supply of  heavy steam and water;

 

③  Make sure that the power supply  as well as electrical appliances are  typical;

 

④  Open up the steam valve,  pre-heat the  drifting fish pellet machine  blowing chamber, the temperature is about 100 degrees;

 

⑤  Begin the fish feed floating pellet making machine: start the conditioner,  begin the feeding auger, when there is  product  spurting from the  electrical outlet of the conditioner,  begin adding  vapor to the conditioner.

 

A small amount of water is added,  and also the material is fed  right into the puffing  tooth cavity at the same time. After the material is extruded by fish feed floating pellet making  device, the puffing  result  as well as  wetness of the  item are  changed.

 

Related post： https://www.richipelletmachine.com/fish-feed-mill-plant/

 

( 3) Downtime

 

After the fish feed floating pellet making  maker production  concerns an end, it  requires to be stopped. The  quit sequence is: feeding auger  as well as conditioner. Then wait until the indicated  worth of the main engine  existing on the electric control cabinet becomes the no-load  present  worth, then  quit the  primary  electric motor  as well as the oil pump  electric motor.

 

( When the corn is  blown,  concerning 25 kg of soybeans  need to be fed  right into the bypass feeding port of the first  area of the puffing  tooth cavity. To  clean up the residual corn  product in the puffing  tooth cavity,  and afterwards  quit the main motor  to stop the fish feed  drifting pellet making  maker from  obstructing), then  swiftly disassemble the puffing  dental caries of the tail  area for  cleansing.

 

After cleaning, apply grease to the inner  wall surface of the  primary shaft  and also screw head (After feeding grease), re-install it  and also  await the  following boot;

 

When you see that the material  degree  indication on the silo indicates that the  product  degree  has actually  gotten to the lowest  degree, start to prepare for  closure.  Right now, do not  quit the feeding auger  as well as conditioner,  and also stop feeding when the main fish feed floating pellet making  maker  existing  declines to the no-load  present auger and conditioner.

 

Related post： Fish Feed Production Plant

 

2. Operation  series of floating fish feed machine

 

( 1 )When puffing soybeans,  both  areas at the inlet end of the puffing cavity are  solitary screw heads,  and also the  3 sections at the outlet end are equipped with double screw heads.

 

 Initially, add  vapor to the  coat to preheat the puffing  dental caries to  concerning 100 degrees,  as well as put the screws on the puffing  dental caries at the tail  area. After the plug is tightened, loosen it for 3-4 turns, and then tighten the screw plug to fix the screw plug before feeding.

 

By controlling the stepless high-speed mechanism of the feeding auger, the feeding speed is from  slow-moving to  quickly,  as well as the feeding speed is from  little to large. After the soybean meal is ejected from the screw plug  opening,  include the cover to enter the normal production,  and also  set up the screw  connects with  various apertures to  acquire soybean meal with  various yields and finenesses.

 

By configuring the conical pressure rings of different  sizes, the  shown  temperature level of the four-section (discharge end)  blowing  tooth cavity is 130-140 degrees. It is  advised that the  filter of the crusher  made use of for crushing soybeans should have a diameter of 3-4.

 

( 2 )When  squeezing out powdery feed by fish feed floating pellet making  maker, the extruding screws in the  squeezing out cavity are all single screw heads,  include steam to the jacket to preheat the puffing  tooth cavity to  regarding 80 degrees, and  get in the fish feed floating pellet making  maker and  heavy steam uniformly  appeased  and also  toughened up powder. my website

 

 Concerning 18%, this must be  carried out in the feed conditioner,  as well as the feed amount is  regulated by the stepless speed  managing  system from  little to  big. Note that the reading of the ammeter of the main  electric motor  must not exceed the  ranked  existing of the main engine of fish feed  drifting pellet making machine.

 

 Be careful of overloading the  electric motor and extruding  fine-grained  products. When the temperature of the extruding chamber at the discharge end is  managed to an  ideal degree by configuring  conelike  stress rings with  various  sizes.

 

 

The above is the principle, structure  and also  running  treatments of the fish feed  drifting pellet making machine  presented by Richi  Equipment. In pursuit of  crunchy taste  as well as good appearance, manufacturers  frequently  include a  raising  representative (or  cooking powder), which  includes a  particular  quantity of aluminum elements,  as well as  creates gas when heated  throughout baking or frying,  and also the  raising  representative is inside the food.