The ring die and the pressing roller of the biomass pellet making equipment turn at a consistent rate, and also the functioning state of each instant is essentially the very same. If the quantity of feed material is the same, the power intake should likewise be fairly steady, and the existing will be reviewed the motor. Additionally relatively secure.
When the biomass pellet making equipment maker is functioning, we adjust the feeding amount as long as the product density in the feeding area is less than the maximum beginning factor of the pressing area, it will straight affect the size of the efficient working area of the pressing location and also journalism location, and cause the present to stream.
The change and also the adjustment of the per hour result of the biomass pellet making equipment, as well as if the thickness of the product layer in the feeding area is more than the optimum beginning factor of journalism location, in addition to boosting the thickness of the product layer in the feeding location, it will not impact the hourly outcome and also power consumption each time.
If there is any influence, it will no longer create modifications in existing and biomass pellet making maker result. Due to the fact that the density of the product layer in the feeding area goes beyond the optimum beginning factor of journalism area, the period between journalism zone and the pressing zone is constant without any modification. In the interval where the multi-feed product is located, the securing angle is more than the essential friction angle, and the product will certainly not be squeezed right into journalism location.
This way, with the rise of the feeding amount of the biomass pellet making machine, the balance of in and out is damaged, and the in is greater than the out, as well as the material layer in the feeding area is It will gather thicker and also thicker until all the voids are filled up and blocked to the feed port, to make sure that the biomass pellet machine can not function typically. Currently, the current will certainly increase.
In the real job of the biomass pellet making device, with the adjustment of the feeding amount, the instant outcome and also the current of the primary motor will alter accordingly. And also when the feeding thickness does not exceed the maximum beginning factor of the pressing location, it will not cause more and more worldly layers in the feeding area as a result of the rise in the amount of powder we feed.
As has been said prior to, the location that can create instantaneous result and also energy intake changes must be both locations of work and product layers - the compression location and also the biomass pellet machine extrusion location, so we assume that the third area discussed over- - The affordable presence of the feeding area has particular problems.
That is to claim, the fed product layer is distributed in the compaction area, the extrusion location and the feeding location whose overall thickness does not go beyond the maximum entrance point of the compaction area.
The biomass pellet making machine will certainly work typically under the allowable power. If the quantity is too large and also surpasses the thickness of the maximum starting factor of the compaction area, the product layer will collect as well as progressively boost, and also the biomass pellet making equipment will not function normally. Current is rising and fall.
With the above evaluation, let's go over some sensations exhibited by the biomass pellet making maker under 2 possible working problems:
( 1 )When the power of the major electric motor is not large enough compared to the matching biomass pellet making equipment granulation specifications, the density of our feed goes to the end of the extrusion area and also the maximum entrance point of the compression area (this will vary with the raw materials, compression ratio, effective length-diameter proportion, moisture, stress rollers and also various other variable aspects to change as necessary), usually will not go beyond the maximum beginning factor, with the boost of the feeding quantity, the compression area will alter as necessary.
The length of the period will certainly be reduced, and also the interval size of the press area will gradually boost appropriately, as well as the current of the primary motor will certainly additionally slowly boost up until it gets to the maximum allowable usage. If the current reaches the defense value we set, and also the thickness of the feeding material has not gone beyond the density of the maximum starting point of the biomass pellet machine pushing area, if the feeding quantity is enhanced, the safety and security system will act, and the excess powder will certainly be discharged. In order to ensure the typical feature of biomass pellets.
( 2 ) Mean the power of the major electric motor is huge or the electric motor fails to overload after the density of the feeding material exceeds the thickness of the optimum beginning factor of journalism location due to the thorough changes of many variables. Right now, the powder fed to the people can not raise the time result, nor will certainly it trigger the boost of the primary electric motor present, however can just continue to raise the powder heap built up in the maker until the inner cavity of the biomass pellet press maker is blocked.
Cause the biomass pellet making equipment to not function correctly. Naturally, this unique sensation seldom happens in real production (if the raw material dampness is as well large, the reliable facet ratio is also small, the pressure roller is badly worn and the gap is not adjusted correctly, the raw material is replaced, and so on, this phenomenon might take place), this is our undesirable problems.
In-depth analysis of the initial commonly made use of functioning state, it is simple to understand that on the property that the appropriate problems are the same, with the modification of the feeding quantity, the interval length of the compression zone and also the extrusion zone is within a certain variety Matching modifications are likewise made (the feed circulation price is lowered, the size of the extrusion area is lowered, and also the length of the compression area is prolonged; otherwise, the extrusion zone is extended and also the compression area is reduced), as well as the feeding amount does not surpass the pressure. When the thickness of the maximum beginning point of the limited area is concerned, the lengths of the above two intervals are not a constant value when this article is written. The larger the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.
Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.
RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!
