Staff Writer-Walter Daley

Plumbing has so many possibilities as to what you can use, do, and how you can apply it to your own plumbing jobs. It is rare to find somebody that has plumbing needs just like you, so why not take advantage of that and perfect your own? This article can help you.

Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. Flux retards oxidation when the copper is heated. Always use find more information -free or nearly lead-free solder when sweating a copper joint.

On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.







Solder with safety in mind. When pipe clog solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected.

Never try to fix a garbage disposal by putting your hand down into it. Even when in the off position, garbage disposals are dangerous. Look for a diagram of the garbage disposal you have on the Internet.

Check your faucets for leaks. Check the knobs and the faucet itself. Hundreds of gallons of water a day can be wasted due to leaks and that's not good if you're paying your water bill. By stopping a leak now, you can save yourself a lot of money. Leaks can grow over time as well, so avoid a disaster and check all faucets for leaks!

Group all of your plumbing repairs before scheduling a plumber to come out. Check all of your fixtures and faucets. If anything is dripping, running or clogged, make a list for the plumber. That way, when the plumber comes, they can do all of the jobs in one visit. This will cut down on charges.

If your toilet is constantly developing moisture on the outside, you may want to consider turning up the heat in your bathroom. The biggest cause of "sweaty" toilets is cool and moist air. Believe it or not, this moisture could actually cause damage to your toilet, so it is crucial that you fix the problem.

There are two ways to remove clean out plugs. You can loosen the fitting with a hammer and a chisel. The only other thing you can do is chisel through it.

Make sure you shut off your main system before leaving your house for a few weeks. The water will stay in the pipes, but this should prevent any further damages in case a leak starts while you are away. Check that your shut-off valve is working properly before you leave.

In the winter months, if you live somewhere where temperatures fall below freezing, leave your faucets on a little bit to let a thin stream of water through. This will help prevent the pipes from freezing, which could be a major problem for you and all the pipes in your home.

Never flush menstrual products, such as pads or tampons, even if the box says it's okay. These products can cause major clogs in your plumbing that cannot be removed with a simple plunger. Ensure that all women in your household understand the importance of placing these items in an appropriate receptacle.

For people who live in an apartment complex, plumbing is often forgotten about. The first time they move into a home they are unable to resolve any minor plumbing problems, because they have never dealt with this kind of thing. It is good to get a basic understanding when moving into your first house.

Heat up frozen pipes carefully if they have frozen. In colder regions, pipes placed closest to outer walls and ceilings could freeze if not properly insulated. Use hot rags, hot water, a blow dryer or similar heat source. Start heating at a place nearest the tap, then work backwards.

Make sure that you check all of the connections after doing any work on a hot water heater, especially pipes that connect to the pipe used for drainage. It is most likely a recirculation pipe, which really goes a long way to help your water stay heated without wasting as much water in the process.

Select your drain cleaners carefully. Some of the chemicals used in these products can damage pipes. Choose a brand known for protecting pipes. Certain chemicals can kill bacteria that are important in your pipes, or even be poisonous.

The water heater in your home needs to have regular flushing to its plumbing in order to work properly. There is usually a valve at the bottom of the water heater that a hose can be attached to. Connect a hose to this valve and open it up all the way to flush scale and deposits out of the system.

A great plumbing tip which can save you a lot of money on a daily basis is to invest in a low GPF (gallons per flush) model toilet. As such, every time you flush the toilet you will be using less water than before, and doing so will save you on your water bill.

Check for calcium and mineral deposits by turning on both the kitchen sink and the bathtub. If the volume of water is low, it may be time for you to replace pipes due to deposits of calcium and other minerals. Check the water pressure and consider calling a professional to handle the entire job.

In conclusion, you could look far and long but will not find a greater collection of advice regarding plumbing other than what you were just exposed to. Use this information and pass it on to those that you know in order to remove any risks that faulty plumbing might cause.