The biggest Maker Faire in Czechia is back in full force! Czech DIYers, inventors, designers and creators will finally meet again offline in Prague this weekend (11th and 12th September) as Maker Faire Prague is just around the corner. Held in the inspiring premises of the Industrial Palace (V'ystaviste Praha), the largest Czech Maker Faire [&]

The post Maker Faire Prague Goes Big Again in 2021 appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/hqwSjdpuGhQ/

Spark safely with these responsible Tesla coil tips from the pros

The post High Voltage! Put Safety First During Your Tesla Coil Performance appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/kMSgURRppes/

When Covid killed their live gigs, musical group ArcAttack pivoted to create their first DIY musical Tesla coil kit. Then the pandemic struck again.

The post Struck Twice: How Musical Group ArcAttack Went From Live Shows to DIY Tesla Coil Kits appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/C-WpsMDWmoM/

Learn how to make curves, and other complex shapes

The post Advanced Techniques For Prototyping With Wood appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/zFGN362idd8/

Maybe it melts, maybe it comes out fine!

The post 400,000-Volt Extreme Thor Cosplay appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/WFwp5Yc_klM/

We aimed to make every repair possible for someone who had never been inside a computer before

The post How I Built Framework, The Laptop Tackling The Right To Repair appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/79BlPYB7VnU/

There can never be enough Bob's Burgers costumes

The post Make Your Own Kuchi Kopi From Bobs Burgers appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/94DOfaqc7rs/

Explore the basics of building models of wood

The post Tips And Tricks For Basic Wooden Model Making appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/V7FWBIsbiCY/

I first met Dr. Steve M. Potter at Maker Faire Atlanta, which was then hosted by Georgia Tech, where he was a professor of neuroengineering. He describes this field as the intersection of brain science and technology. His life experience combines the curiosity that led him to study how learning happens in the brain, the [&]

The post The Making of a Scientist/Maker/Teacher appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/qYFmpcc_zxQ/

Name  Josh Waddell Where are you located? Bartlesville What is your day job?  Full time maker! Owner / Operator of 3 Bulls UPcycling, LLC Find me on Instagram Do you attend a makerspace/fablab/hackerspace?  Yes I have my own workshop that I rent. What kinds of stuff do you make? We make a variety of hand [&]

The post Maker Spotlight: Josh Waddell of 3 Bulls UPcycling appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/ivOajp55zSE/

Collaboration is key, especially when it comes to faculty

The post University Makerspaces 3: Collaborating with Faculty appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/GcEHXSmUJHg/

meet Zach!

The post Maker Spotlight: Zach Raw appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/f45vH9j8S4E/

Meet Geeky Faye!

The post Maker Spotlight: Geeky Faye appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/q6AA0-hxEX4/

previously, 2 part primer was just for the pros. Now it comes in a rattle can!

The post How 2 Part Primer In A Rattle Can Makes Props Look Great appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/hp8iqu-s2ok/

Expand your Audience Reach: Support from University Staff University staff members are vast and wide in their exposure to the student population. They are responsible for aiding students in their on-campus experience outside of the academic setting. Staff members may serve the students as club leaders, mentors, and advisors in addition to their day-to-day role. [&]

The post University Makerspaces 2: Support from Staff appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/oPT3P9lTMq4/

Kinetic artist Jim Polk created the mechanisms to animate a three-toed sloth puppet, giving it a head that can turn and eyes that blink.

The post How to Animate a Sloth Puppet appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/trX-f1728Ak/

when it comes to making large molds, there's a lot to keep in mind

The post Tips For Making A Large Silicone Mold appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/HwMqXbzDXVY/

Maker Faire Asuncion is here! join up virtually and enjoy

The post Asunci'on Virtual Maker Faire Is This Weekend! appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/xeVb-rzJKiI/

Part 1 of a series on growing and running university based makerspaces

The post University Makerspaces 1: Generating Student Buy-in appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/2K44Oxpikco/

Parker Thomas had an idea for a bag that he turned into a handmade prototype. He launched one Kickstarter, then another to create version one, and then two of the product. He had to figure out how to make it first in Oakland, near where he lives and then in Vietnam. Throughout this process, he [&]

The post Making Customizable Tool Rolls appeared first on Make: DIY Projects and Ideas for Makers.

http://feedproxy.google.com/~r/makezineonline/~3/M_8sXAOju8Q/